BusyDizzys

...

nse:] -->

GM

1. Close all the vehicle doors.

2. Insert the ignition key into the ignition lock cylinder - do not turn ignition switch.

3. Press and hold the DOOR unlock switch (This is the switch on the door, NOT the remote).

4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF two or three times. If the door lock clicks after the second ON, OFF cycle do not do it a third time.

5. Release the DOOR unlock switch. The doors will lock and unlock one time to confirm the program mode is activates.

6. Simultaneously press and hold the LOCK button and the UNLOCK button on one keyless remote for approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.

7. Repeat the previous step to program up to four transmitters.

8. Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode.

9. Operate the transmitter functions in order to verify correct system operation.

Ford

1. Insert a key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) with the eighth turn ending in the ON position.

2. The doors will lock/unlock to confirm that programming mode has been entered.

3. Within 20 seconds, program a remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.)

4. Repeat the previous step to program additional remote transmitters. The doors will lock/unlock to confirm that each remote transmitter has been programmed.

5. When you have completed programming the remote transmitters, turn th ignition to OFF or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.

Dodge

1. Turn your key to the "Run" position, but do not start the engine. Shut the doors and wait for the warning beeps to stop.

2. Hold the "Unlock" button on the currently programmed remote for five seconds, and then press and hold the "Panic" button (while still holding "Unlock") for one second.

3. Press and hold the "Lock" and "Unlock" button on the same remote for a few seconds, then release the buttons and press the "Unlock" button.

4. Press and hold the "Lock" and "Unlock" button on the new remote, then release the buttons and press the "Unlock" button. Repeat the procedure for up to four remotes within 30 seconds.

Dodge Ram (2002 to 2005)

1. Sit in the driver's seat and buckle the seat belt. Make sure all the doors are closed. Put your key in the ignition and turn it to "On." This mode turns on your electronics without cranking the engine.

2. Hold "Unlock" on your working keyless-entry remote. After four seconds, press "Panic" while holding "Unlock." You'll hear a warning chime; release both buttons.

3. Press and release "Unlock" and "Lock" simultaneously on the keyless-entry remote you are programming.

4. Listen for the warning chime. Press "Lock" on the remote you are programming within four seconds of hearing the chime. You'll hear another chime. This indicates the remote is programmed.

Dodge Dakota and Durango (2001 to 2004)

1. Take a seat in your vehicle and close the door. Press "Lock" on a currently-programmed remote five times, allowing two seconds to pass between each press.

2. Place your key in the ignition. Turn it to "Run." Keep it in run until the chiming stops. Once the chiming stops, press and hold "Lock" for four seconds on the programmed remote. After four seconds, press and hold "Panic" along with "Lock" for one second, and then release both buttons. Listen for a single chime.

3. Press and release "Unlock" and "Lock" on the remote you want to program, and then press and release "Unlock." Listen for a single chime. This indicates the remote is programmed.

Dodge Neon (2000 to 2006)

1. Place the key in the ignition. Turn it to "Run." Press and hold "Unlock" for four seconds on the programmed remote.

2. Press and hold "Panic" for one second, while holding "Unlock," and then release both buttons. Listen for the chime.

3. Press any button on the remote you want to program. A single chime is heard, indicating the remote is programmed. Press any button on the previously-programmed remote (it must be resynchronized). Turn the engine off and test each remote.

Toyota

1. Ensure the car doors are unlocked and open. Pull the key from the ignition.

2. Insert and remove the key from the ignition two times within five seconds. This will start the required sequence to reprogram the car's computer.

3. Close and open the driver's door twice within 40 seconds. This step has to be within that time, or the system will reset.

4. Insert the key into the ignition. Do not turn the key yet.

5. Cycle the key from "lock" to "on." You will need to cycle this step one time for the "add" mode.

6. Remove the key from the ignition. Immediately grab the transmitter to complete the program.

7. Press both the lock and unlock buttons on your transmitter simultaneously for 1 to 1 1/2 seconds. Release the buttons afterwards.

8. Press the lock button within three seconds of releasing on the last step. This will complete the process. The door locks will cycle from lock to unlock if the process is done correctly. If there is a problem, the lock will cycle twice.

9. Open the driver's door. This will complete the process.

Nissan

1. Open the driver’s side door of  and get in the vehicle. Close the door. Press the lock button on the driver’s side door to lock all the doors.

2. Insert your key into the ignition and remove it at least 6 times. It may take up to 10 times. This needs to be done in a good pace, but not too fast. At least 6 times within 10 seconds is about right. If you have done it right, you will see the hazard lights flash twice.

3. Once you see the hazard lights flash twice, the car is now in program mode. Insert the key back into the ignition and turn it to ACC. Push any button on your keyless entry FOB remote ONCE. This should be done within 5 seconds of turning the key to ACC. You should notice your hazards flash again. If you have another remote to program proceed to step 4, otherwise turn the key off and remove it. The remote should now be programmed.

4. If you have another keyless entry remote to program unlock the door with the driver’s side power lock and then lock them again. Press any button on the next remote. Turn the key back to the original position and remove the key. The remotes should now be programmed.